How To Make A Hallway Table: 6 Simple Step?

You can easily make a hallway table at home.

A lovely hallway table will not only adorn the beauty of your house but also become a convenient place for storing your belongings. So, how to make a hallway table: 6 simple steps?

There are many ways to make your hallway table stand out. But as a beginner, you might think that the building process is way too complicated.

Let’s set aside the troublesome process, this writing will give you the most simple solution for building a table saw for beginners in just a six-step procedure!

How To Make A Hallway Table: 6 Simple Step.

Step 1: Prepare the Materials

You will need:

  •         Four poplar end rails
  •         Two oak stiles
  •         Four poplar legs
  •         Two side rails of poplar
  •         One middle rail of poplar
  •         One stretcher from oak
  •         Three top slats oak

You can have a saw table for beginner

Step 2:  Build Up The Side Pieces

On the two ends of stiles, you drill two pocket holes. Stain the above stiles and leave them there to dry. On the end rails, you stick stiles at the center. Next, you add glue and insert the plugs into the pocket holes.

Now you can start painting the legs of the table. When they are dry, you insert the legs into the stile assemblies’ end. If you aren’t a DIY person, it’d better have a look at https://www.discoveriesla.com/best-portable-table-saw-for-fine-woodworking to find a table saw for beginners.

Step 3: Build The Base & Connect The Sides

On the two ends of the stretcher, you drill and paint the pocket holes. Then you need to drill the pocket holes perpendicularly to the assemblies tops to keep side rails.

Create the end rails layout and position the middle one with glue at the side rails’ center.

You stick the stretcher at the center and in line with the end edge of the last rails.

Step 4: Form The Top

You position the end grain at the center of the up curve and the down curve. Apply glue on the edges and stick the parts with flush ends and lightly clamp.

On slats and cauls top, you need to tighten the clamps and make adjustments if needed. Next, you can cut the last top assembly following the table’s saw or in a circle.

Lastly, you can apply paint to all parts of the top.

Step 5: Arrange All Parts Together

For the next step, you put the top part of the table at the center of the assembly base and use 1/4-inch pocket hole screws as a connection.

Step 6: Carry Out The Finishing Steps

In the pocket holes, you apply some glue and insert paintable plugs. Finally, to have a wonderful hallway table, you should clean the excess glue and paint it if necessary.

Sum up

With all the detailed instructions above, you might now have an overview of how to make a hallway table: 6 simple steps, haven’t you?

It is not hard to follow. You only need to prepare things fully and practice steps carefully. Hope you have the best hallway table ever! Cheer!

Bosch Glide Miter Saw Problems With Best Solution

After a use time, your old Bosch Glide Miter Saw begins having some problems that make you hard to complete your woodwork? However, you do not want to use the customer service because of its huge cost, instead of you decide to solve the issue by yourself.

No problem! We will help you by offering the best solutions for the problems of your Bosch Glide Miter Saw.

Roll down!

Bosch Glide Miter Saw Problems With Best Solution

Problems of Your Bosch Glide Miter Saw

Throughout using the Bosch Glide Miter Saw, you might meet a couple of frustrating problems. In particular, here are:

Incapable Dust Collection

Sawdust going via the provided hose will gradually stick all over the back of the saw. Even in case, a machine has a dust bag to plug into the 90-degree hose, it is not enough to make you satisfied. The simple reason is due to its bend, making the airflow as well as suction power reduce.

For fixing the dust collection problem,  it would be best to connect the miter saw with your worksite table saw. As a useful reference source, you can access https://www.discoveriesla.com/bosch-4100-09-review to look up more information.

Tear-out problems

There is probably a clearance between the blade and the insert edges (you likely get the knowledge related to this at Home Improvement Blog). Hence, your work becomes less supportive, and the board bottom can appear in the tear-out problem. Finally, you cannot perform clean cuts at all

Best Solutions

Let’s feel secure because you can get rid of the hassles of your older Bosch Glide Miter Saw by following upgrades below:

Modify your Dust Collection

For removing the 90° bend, you start twist-pulling it off and installing the dust hose onto your miter saw’s the plastic dust shroud. Continuously, direct this hose in a place where you want to. Make sure that you will see an awesome difference? It is noticeable that sawdust will not fly all over your woodwork place.

Make a Zero Clearance Insert

A Zero Clearance Insert

Start to measure the throat plate of your miter saw. Next, cut a part of plywood with thickness and length accordingly. You’d better remember to position the screw holes on the zero clearance insert, and drilling them. The last one, build in that insert in the location of the throat plate, making clean cuts on it (from up and down).

In Sum

For the time being, have you probably got helpful tricks to improve the performance of your miter saw? Yes, you might perform cuts in the sharper way without tearing-out while the problems related to sawdust are free.

We hope that your Bosch Glide Miter Saw becomes better after following our solutions.

Do it your way!

You have been using your Bosch Glide Miter Saw for a while but now run into some problems that frustrate you and your woodwork? Instead of calling the customer service and getting ready for the hefty shipping fee to get them fixed, you want to compromise by yourself?

No more worries, here we provide some of the best solutions for problems of your Bosch Glide Miter Saw.

How to Pick Up Great Knives for Your Kitchen

Did you know?

Choosing a good knife set and other related cooking stuff for your kitchen is usually one of the must-do tasks whenever you want to remodel your kitchen.

However, it’s easier to talk than actually do. So, how can you really find and bring home great knives that can change your cooking experience?

Let’s talk about some great tips in this short post.

The first tip that I want to share is to always choose a great chef knife since it’s considered the all-in-one cooking knife every home cook and chef should own.

A great damascus chef knife is ideal since that type of chef knife is really hard and solid. It’s also sharp and does look good also.

You can do a lot of chopping, cutting, mincing tasks with it down the road for sure.

Another thing that you will need to buy is a set of knife sharpener.

Why?

It’s because you’ve spent a lot of money on a good chef knife, you won’t want to lose its sharpness so quickly that you will have to buy a new one just a few months later.

So, what kind of sharpener should you choose?

Based on my experience, electric sharpeners would be optimal. Because they won’t require you to know too much about knife sharpening, and they also take less time as well.

But the downside is that they often cost more compared to traditional whetstones.

And finally, if you’re planning to do a lot of small tasks like deboning, filleting fishes, etc. then a good knife for filleting should be required as well.

It’s a small, specialized edge that often deals with filleting fishes and deboning as well. It often doesn’t cost much, so you won’t have to worry about if it would break the bank.

And if you have to choose the brands where you would shop those products from, then I highly recommend the ones like Dalstrong, Zelite Infinity, Wusthof, etc.

They will surely give you the best bang for your bucks.